Android Boot Image

Overview

Android Boot Image is used to boot Android OS. It usually contains kernel image (like zImage file) and ramdisk. Sometimes it can contain additional binaries. This image is built as a part of AOSP (called boot.img), and being flashed into boot partition on eMMC. Bootloader then reads that image from boot partition to RAM and boots the kernel from it. Kernel then starts init process from the ramdisk. It should be mentioned that recovery image (recovery.img) also has Android Boot Image format.

Android Boot Image format is described at [1]. At the moment it can have one of next image headers:

  • v0: it’s called legacy boot image header; used in devices launched before Android 9; contains kernel image, ramdisk and second stage bootloader (usually unused)

  • v1: used in devices launched with Android 9; adds recovery_dtbo field, which should be used for non-A/B devices in recovery.img (see [2] for details)

  • v2: used in devices launched with Android 10; adds dtb field, which references payload containing DTB blobs (either concatenated one after the other, or in Android DTBO image format)

  • v3: used in devices launched with Android 11; adds vendor_boot partition and removes the second-stage bootloader and recovery image support. The new vendor_boot partition holds the device tree blob (DTB) and a vendor ramdisk. The generic ramdisk in boot partition is loaded immediately following the vendor ramdisk.

  • v4: used in devices launched with Android 12; provides a boot signature in boot image header, supports multiple vendor ramdisk fragments in vendor_boot partition. This version also adds a bootconfig section at the end of the vendor boot image, this section contains boot configuration parameters known at build time (see [9] for details).

v2, v1 and v0 formats are backward compatible.

The Android Boot Image format is represented by struct andr_image_data in U-Boot, and can be seen in include/android_image.h. U-Boot supports booting Android Boot Image and also has associated command

Booting

U-Boot is able to boot the Android OS from Android Boot Image using bootm command. In order to use Android Boot Image format support, next option should be enabled:

CONFIG_ANDROID_BOOT_IMAGE=y

Then one can use next bootm command call to run Android:

=> bootm $loadaddr $loadaddr $fdtaddr

where $loadaddr - address in RAM where boot image was loaded; $fdtaddr - address in RAM where DTB blob was loaded.

And parameters are, correspondingly:

  1. Where kernel image is located in RAM

  2. Where ramdisk is located in RAM (can be "-" if not applicable)

  3. Where DTB blob is located in RAM

bootm command will figure out that image located in $loadaddr has Android Boot Image format, will parse that and boot the kernel from it, providing DTB blob to kernel (from 3rd parameter), passing info about ramdisk to kernel via DTB.

DTB and DTBO blobs

bootm command can’t just use DTB blob from Android Boot Image (dtb field), because:

  • there is no DTB area in Android Boot Image before v2

  • there may be several DTB blobs in DTB area (e.g. for different SoCs)

  • some DTBO blobs may have to be merged in DTB blobs before booting (e.g. for different boards)

So user has to prepare DTB blob manually and provide it in a 3rd parameter of bootm command. Next commands can be used to do so:

  1. abootimg: manipulates Anroid Boot Image, allows one to extract meta-information and payloads from it

  2. adtimg: manipulates Android DTB/DTBO image [3], allows one to extract DTB/DTBO blobs from it

In order to use those, please enable next config options:

CONFIG_CMD_ABOOTIMG=y
CONFIG_CMD_ADTIMG=y

For example, let’s assume we have next Android partitions on eMMC:

  • boot: contains Android Boot Image v2 (including DTB blobs)

  • dtbo: contains DTBO blobs

Then next command sequence can be used to boot Android:

=> mmc dev 1

   # Read boot image to RAM (into $loadaddr)
=> part start mmc 1 boot boot_start
=> part size mmc 1 boot boot_size
=> mmc read $loadaddr $boot_start $boot_size

   # Read DTBO image to RAM (into $dtboaddr)
=> part start mmc 1 dtbo dtbo_start
=> part size mmc 1 dtbo dtbo_size
=> mmc read $dtboaddr $dtbo_start $dtbo_size

   # Copy required DTB blob (into $fdtaddr)
=> abootimg get dtb --index=0 dtb0_start dtb0_size
=> cp.b $dtb0_start $fdtaddr $dtb0_size

   # Merge required DTBO blobs into DTB blob
=> fdt addr $fdtaddr 0x100000
=> adtimg addr $dtboaddr
=> adtimg get dt --index=0 $dtbo0_addr
=> fdt apply $dtbo0_addr

   # Boot Android
=> bootm $loadaddr $loadaddr $fdtaddr

This sequence should be used for Android 10 boot. Of course, the whole Android boot procedure includes much more actions, like:

  • obtaining reboot reason from BCB (see [4])

  • implementing recovery boot

  • implementing fastboot boot

  • implementing A/B slotting (see [5])

  • implementing AVB2.0 (see [6])

But Android Boot Image booting is the most crucial part in Android boot scheme.

All Android bootloader requirements documentation is available at [7]. Some overview on the whole Android 10 boot process can be found at [8].

C API for working with Android Boot Image format

int android_image_get_kernel(const void *hdr, const void *vendor_boot_img, int verify, ulong *os_data, ulong *os_len)

processes kernel part of Android boot images

Parameters

const void *hdr

Pointer to boot image header, which is at the start of the image.

const void *vendor_boot_img

Pointer to vendor boot image header, which is at the start of the image.

int verify

Checksum verification flag. Currently unimplemented.

ulong *os_data

Pointer to a ulong variable, will hold os data start address.

ulong *os_len

Pointer to a ulong variable, will hold os data length.

Description

This function returns the os image’s start address and length. Also, it appends the kernel command line to the bootargs env variable.

Return

Zero, os start address and length on success,

otherwise on failure.

bool android_image_get_dtbo(ulong hdr_addr, ulong *addr, u32 *size)

Get address and size of recovery DTBO image.

Parameters

ulong hdr_addr

Boot image header address

ulong *addr

If not NULL, will contain address of recovery DTBO image

u32 *size

If not NULL, will contain size of recovery DTBO image

Description

Get the address and size of DTBO image in “Recovery DTBO” area of Android Boot Image in RAM. The format of this image is Android DTBO (see corresponding “DTB/DTBO Partitions” AOSP documentation for details). Once the address is obtained from this function, one can use ‘adtimg’ U-Boot command or android_dt_*() functions to extract desired DTBO blob.

This DTBO (included in boot image) is only needed for non-A/B devices, and it only can be found in recovery image. On A/B devices we can always rely on “dtbo” partition. See “Including DTBO in Recovery for Non-A/B Devices” in AOSP documentation for details.

Return

true on success or false on error.

bool android_image_get_dtb_img_addr(ulong hdr_addr, ulong vhdr_addr, ulong *addr)

Get the address of DTB area in boot image.

Parameters

ulong hdr_addr

Boot image header address

ulong vhdr_addr

Vendor Boot image header address

ulong *addr

Will contain the address of DTB area in boot image

Return

true on success or false on fail.

bool android_image_get_dtb_by_index(ulong hdr_addr, ulong vendor_boot_img, u32 index, ulong *addr, u32 *size)

Get address and size of blob in DTB area.

Parameters

ulong hdr_addr

Boot image header address

ulong vendor_boot_img

Pointer to vendor boot image header, which is at the start of the image.

u32 index

Index of desired DTB in DTB area (starting from 0)

ulong *addr

If not NULL, will contain address to specified DTB

u32 *size

If not NULL, will contain size of specified DTB

Description

Get the address and size of DTB blob by its index in DTB area of Android Boot Image in RAM.

Return

true on success or false on error.

void android_print_contents(const struct andr_boot_img_hdr_v0 *hdr)

prints out the contents of the Android format image

Parameters

const struct andr_boot_img_hdr_v0 *hdr

pointer to the Android format image header

Description

android_print_contents() formats a multi line Android image contents description. The routine prints out Android image properties

Return

no returned results

bool android_image_print_dtb_info(const struct fdt_header *fdt, u32 index)

Print info for one DTB blob in DTB area.

Parameters

const struct fdt_header *fdt

DTB header

u32 index

Number of DTB blob in DTB area.

Return

true on success or false on error.

bool android_image_print_dtb_contents(ulong hdr_addr)

Print info for DTB blobs in DTB area.

Parameters

ulong hdr_addr

Boot image header address

Description

DTB payload in Android Boot Image v2+ can be in one of following formats:
  1. Concatenated DTB blobs

  2. Android DTBO format (see CONFIG_CMD_ADTIMG for details)

This function does next:
  1. Prints out the format used in DTB area

  2. Iterates over all DTB blobs in DTB area and prints out the info for each blob.

Return

true on success or false on error.

References