U-Boot for JetHub J100/J110 (A113X)

JetHome Jethub D1/D1+ (http://jethome.ru/jethub-d1p) is a home automation controller device manufactured by JetHome with the following specifications:

  • Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz

  • no video out

  • 512MB/1GB DDR3 or 2GB DDR4 SDRAM

  • 8/16/32GB eMMC flash

  • 1 x USB 2.0

  • 1 x 10/100Mbps ethernet

  • WiFi / Bluetooth one from: - AMPAK AP6255 (Broadcom BCM43455) IEEE 802.11a/b/g/n/ac, Bluetooth 4.2 - RTL8822CS IEEE 802.11a/b/g/n/ac, Bluetooth 5.0 - Amlogic W155S1 WiFi5 IEEE 802.11a/b/g/n/ac, Bluetooth 5.2

  • 2 x gpio LEDS

  • GPIO user Button

  • DC source with a voltage of 9 to 56 V / Passive POE

  • DIN Rail Mounting case

The basic version also has:

  • Zigbee module one from: - TI CC2538 + CC2592 Zigbee 3.0 Wireless - TI CC2652P1 Zigbee 3.0 Wireless - Silicon Labs EFT32MG21 Zigbee 3.0/Thread Wireless

  • 1 x 1-Wire

  • 2 x RS-485

  • 4 x dry contact digital GPIO inputs

  • 3 x relay GPIO outputs

U-Boot Compilation

$ export CROSS_COMPILE=aarch64-none-elf-
$ make jethub_j100_defconfig
$ make

U-Boot Signing with Pre-Built FIP repo

$ git clone https://github.com/LibreELEC/amlogic-boot-fip --depth=1
$ cd amlogic-boot-fip
$ mkdir my-output-dir
$ ./build-fip.sh jethub-j100 /path/to/u-boot/u-boot.bin my-output-dir

U-Boot Manual Signing

Amlogic does not provide sources for the firmware and tools needed to create a bootloader image so it is necessary to obtain binaries from sources published by the board vendor:

$ git clone https://github.com/jethome-ru/jethub-aml-tools jethub-u-boot
$ cd jethub-u-boot
$ export FIPDIR=$PWD

Go back to the mainline U-Boot source tree then:

$ mkdir fip

$ cp $FIPDIR/j100/bl2.bin fip/
$ cp $FIPDIR/j100/acs.bin fip/
$ cp $FIPDIR/j100/bl21.bin fip/
$ cp $FIPDIR/j100/bl30.bin fip/
$ cp $FIPDIR/j100/bl301.bin fip/
$ cp $FIPDIR/j100/bl31.img fip/
$ cp u-boot.bin fip/bl33.bin

$ $FIPDIR/blx_fix.sh \
    fip/bl30.bin \
    fip/zero_tmp \
    fip/bl30_zero.bin \
    fip/bl301.bin \
    fip/bl301_zero.bin \
    fip/bl30_new.bin \
    bl30

$ $FIPDIR/acs_tool.pyc fip/bl2.bin fip/bl2_acs.bin fip/acs.bin 0

$ $FIPDIR/blx_fix.sh \
    fip/bl2_acs.bin \
    fip/zero_tmp \
    fip/bl2_zero.bin \
    fip/bl21.bin \
    fip/bl21_zero.bin \
    fip/bl2_new.bin \
    bl2

$ $FIPDIR/j100/aml_encrypt_axg --bl3sig --input fip/bl30_new.bin \
                               --output fip/bl30_new.bin.enc \
                               --level v3 --type bl30
$ $FIPDIR/j100/aml_encrypt_axg --bl3sig --input fip/bl31.img \
                               --output fip/bl31.img.enc \
                               --level v3 --type bl31
$ $FIPDIR/j100/aml_encrypt_axg --bl3sig --input fip/bl33.bin --compress lz4 \
                               --output fip/bl33.bin.enc \
                               --level v3 --type bl33
$ $FIPDIR/j100/aml_encrypt_axg --bl2sig --input fip/bl2_new.bin \
                               --output fip/bl2.n.bin.sig
$ $FIPDIR/j100/aml_encrypt_axg --bootmk \
                               --output fip/u-boot.bin \
                               --bl2 fip/bl2.n.bin.sig \
                               --bl30 fip/bl30_new.bin.enc \
                               --bl31 fip/bl31.img.enc \
                               --bl33 fip/bl33.bin.enc --level v3

Then write U-Boot to SD or eMMC with:

$ DEV=/dev/boot_device
$ dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1
$ dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=440