QEMU RISC-V

QEMU for RISC-V supports a special ‘virt’ machine designed for emulation and virtualization purposes. This document describes how to run U-Boot under it. Both 32-bit and 64-bit targets are supported, running in either machine or supervisor mode.

The QEMU virt machine models a generic RISC-V virtual machine with support for the VirtIO standard networking and block storage devices. It has CLINT, PLIC, 16550A UART devices in addition to VirtIO and it also uses device-tree to pass configuration information to guest software. It implements RISC-V privileged architecture spec v1.10.

Building U-Boot

Set the CROSS_COMPILE environment variable as usual, and run:

  • For 32-bit RISC-V:

    make qemu-riscv32_defconfig
    make
    
  • For 64-bit RISC-V:

    make qemu-riscv64_defconfig
    make
    

This will compile U-Boot for machine mode. To build supervisor mode binaries, use the configurations qemu-riscv32_smode_defconfig and qemu-riscv64_smode_defconfig instead. Note that U-Boot running in supervisor mode requires a supervisor binary interface (SBI), such as RISC-V OpenSBI.

Running U-Boot

The minimal QEMU command line to get U-Boot up and running is:

  • For 32-bit RISC-V:

    qemu-system-riscv32 -nographic -machine virt -bios u-boot
    
  • For 64-bit RISC-V:

    qemu-system-riscv64 -nographic -machine virt -bios u-boot
    

The commands above create targets with 128MiB memory by default. A freely configurable amount of RAM can be created via the ‘-m’ parameter. For example, ‘-m 2G’ creates 2GiB memory for the target, and the memory node in the embedded DTB created by QEMU reflects the new setting.

For instructions on how to run U-Boot in supervisor mode on QEMU with OpenSBI, see the documentation available with OpenSBI: https://github.com/riscv/opensbi/blob/master/docs/platform/qemu_virt.md

These have been tested in QEMU 5.0.0.

Running U-Boot SPL

In the default SPL configuration, U-Boot SPL starts in machine mode. U-Boot proper and OpenSBI (FW_DYNAMIC firmware) are bundled as FIT image and made available to U-Boot SPL. Both are then loaded by U-Boot SPL and the location of U-Boot proper is passed to OpenSBI. After initialization, U-Boot proper is started in supervisor mode by OpenSBI.

OpenSBI must be compiled before compiling U-Boot. Version 0.4 and higher is supported by U-Boot. Clone the OpenSBI repository and run the following command.

git clone https://github.com/riscv/opensbi.git
cd opensbi
make PLATFORM=qemu/virt

See the OpenSBI documentation for full details: https://github.com/riscv/opensbi/blob/master/docs/platform/qemu_virt.md

To make the FW_DYNAMIC binary (build/platform/qemu/virt/firmware/fw_dynamic.bin) available to U-Boot, either copy it into the U-Boot root directory or specify its location with the OPENSBI environment variable. Afterwards, compile U-Boot with the following commands.

  • For 32-bit RISC-V:

    make qemu-riscv32_spl_defconfig
    make
    
  • For 64-bit RISC-V:

    make qemu-riscv64_spl_defconfig
    make
    

The minimal QEMU commands to run U-Boot SPL in both 32-bit and 64-bit configurations are:

  • For 32-bit RISC-V:

    qemu-system-riscv32 -nographic -machine virt -bios spl/u-boot-spl \
    -device loader,file=u-boot.itb,addr=0x80200000
    
  • For 64-bit RISC-V:

    qemu-system-riscv64 -nographic -machine virt -bios spl/u-boot-spl \
    -device loader,file=u-boot.itb,addr=0x80200000
    

An attached disk can be emulated by adding:

-device ich9-ahci,id=ahci \
-drive if=none,file=riscv64.img,format=raw,id=mydisk \
-device ide-hd,drive=mydisk,bus=ahci.0

You will have to run ‘scsi scan’ to use it.