U-Boot for Khadas VIM¶

Khadas VIM is an Open Source DIY Box manufactured by Shenzhen Wesion Technology Co., Ltd with the following specifications:

Amlogic S905X ARM Cortex-A53 quad-core SoC @ 1.5GHz

ARM Mali 450 GPU

2GB DDR3 SDRAM

10/100 Ethernet

HDMI 2.0 4K/60Hz display

40-pin GPIO header

2 x USB 2.0 Host, 1 x USB 2.0 Type-C OTG

8GB/16GBeMMC

microSD

SDIO Wifi Module, Bluetooth

Two channels IR receiver

U-Boot compilation¶

$ export CROSS_COMPILE=aarch64-none-elf-
$ make khadas-vim_defconfig
$ make

Image creation¶

Amlogic doesn’t provide sources for the firmware and for tools needed to create the bootloader image, so it is necessary to obtain them from the git tree published by the board vendor:

$ wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
$ wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
$ tar xvfJ gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
$ tar xvfJ gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
$ export PATH=$PWD/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux/bin:$PWD/gcc-linaro-arm-none-eabi-4.8-2013.11_linux/bin:$PATH
$ git clone https://github.com/khadas/u-boot -b Vim vim-u-boot
$ cd vim-u-boot
$ make kvim_defconfig
$ make CROSS_COMPILE=aarch64-none-elf-
$ export FIPDIR=$PWD/fip

Go back to mainline U-Boot source tree then :

$ mkdir fip

$ cp $FIPDIR/gxl/bl2.bin fip/
$ cp $FIPDIR/gxl/acs.bin fip/
$ cp $FIPDIR/gxl/bl21.bin fip/
$ cp $FIPDIR/gxl/bl30.bin fip/
$ cp $FIPDIR/gxl/bl301.bin fip/
$ cp $FIPDIR/gxl/bl31.img fip/
$ cp u-boot.bin fip/bl33.bin

$ $FIPDIR/blx_fix.sh \
    fip/bl30.bin \
    fip/zero_tmp \
    fip/bl30_zero.bin \
    fip/bl301.bin \
    fip/bl301_zero.bin \
    fip/bl30_new.bin \
    bl30

$ python $FIPDIR/acs_tool.pyc fip/bl2.bin fip/bl2_acs.bin fip/acs.bin 0

$ $FIPDIR/blx_fix.sh \
    fip/bl2_acs.bin \
    fip/zero_tmp \
    fip/bl2_zero.bin \
    fip/bl21.bin \
    fip/bl21_zero.bin \
    fip/bl2_new.bin \
    bl2

$ $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl30_new.bin
$ $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl31.img
$ $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl33.bin
$ $FIPDIR/gxl/aml_encrypt_gxl --bl2sig --input fip/bl2_new.bin --output fip/bl2.n.bin.sig
$ $FIPDIR/gxl/aml_encrypt_gxl --bootmk \
            --output fip/u-boot.bin \
            --bl2 fip/bl2.n.bin.sig \
            --bl30 fip/bl30_new.bin.enc \
            --bl31 fip/bl31.img.enc \
            --bl33 fip/bl33.bin.enc

and then write the image to SD with:

$ DEV=/dev/your_sd_device
$ dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1
$ dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=444