Sipeed’s Lichee PI 4A based on T-HEAD TH1520 SoC

The LicheePi4A is a high-performance RISC-V SBC based on TH1520(4xC910@1.85GHz), comes with 4/8/16 GB RAM, and up to 128GB eMMC, and rich peripherals.

  • SoC T-HEAD TH1520 SoC

  • System Memory 4GB, 8GB, or 16GB LPDDR4X

  • Storage eMMC flash with 8/32/128 GB

  • external microSD slot

  • Networking 2x Gigabit Ethernet

  • WiFi+BT

  • Display HDMI2.0, 4-lane MIPI DSI

  • Camera 4-lane MIPI CSI + 2x2-lane MIPI CSI

  • Audio Onboard Speaker, 2xMEMS MIC, 3.5mm headphone jack

  • USB 4xUSB3.0 Type-A, 1xUSB2.0 Type-C

  • GPIO 2x10Pin breakout, UART/IIC/SPI

  • Power DC 12V/2A, POE 5V/2.4A, USB Type-C 5V/2A

TH1520 RISC-V SoC

The TH1520 SoC consist of quad-core RISC-V Xuantie C910 (RV64GCV) processor, Xuantie C906 audio DSP, low power Xuantie E902 core, it also integrate Imagination GPU for graphics, and 4 TOPS NPU for AI acceleration.

Mainline support

The support for following drivers are already enabled:

  1. ns16550 UART Driver.

Building

  1. Add the RISC-V toolchain to your PATH.

  2. Setup ARCH & cross compilation environment variable:

export CROSS_COMPILE=<riscv64 toolchain prefix>

The U-Boot is capable of running in M-Mode, so we can directly build it.

cd <U-Boot-dir>
make th1520_lpi4a_defconfig
make

This will generate u-boot-dtb.bin

Booting

Currently, we rely on vendor u-boot to initialize the clock, pinctrl subsystem, and chain load the mainline u-boot image either via tftp or emmc storage, then bootup from it.

Sample boot log from Lichee PI 4A board via tftp

brom_ver 8
[APP][E] protocol_connect failed, exit.

U-Boot SPL 2020.01-00016-g8c870a6be8 (May 20 2023 - 01:04:49 +0000)
FM[1] lpddr4x dualrank freq=3733 64bit dbi_off=n sdram init
ddr initialized, jump to uboot
image has no header


U-Boot 2020.01-00016-g8c870a6be8 (May 20 2023 - 01:04:49 +0000)

CPU:   rv64imafdcvsu
Model: T-HEAD c910 light
DRAM:  8 GiB
C910 CPU FREQ: 750MHz
AHB2_CPUSYS_HCLK FREQ: 250MHz
AHB3_CPUSYS_PCLK FREQ: 125MHz
PERISYS_AHB_HCLK FREQ: 250MHz
PERISYS_APB_PCLK FREQ: 62MHz
GMAC PLL POSTDIV FREQ: 1000MHZ
DPU0 PLL POSTDIV FREQ: 1188MHZ
DPU1 PLL POSTDIV FREQ: 1188MHZ
MMC:   sdhci@ffe7080000: 0, sd@ffe7090000: 1
Loading Environment from MMC... OK
Error reading output register
Warning: cannot get lcd-en GPIO
LCD panel cannot be found : -121
splash screen startup cost 16 ms
In:    serial
Out:   serial
Err:   serial
Net:
Warning: ethernet@ffe7070000 using MAC address from ROM
eth0: ethernet@ffe7070000ethernet@ffe7070000:0 is connected to ethernet@ffe7070000.  Reconnecting to ethernet@ffe7060000

Warning: ethernet@ffe7060000 (eth1) using random MAC address - 42:25:d4:16:5f:fc
, eth1: ethernet@ffe7060000
Hit any key to stop autoboot:  2
ethernet@ffe7060000 Waiting for PHY auto negotiation to complete.. done
Speed: 1000, full duplex
Using ethernet@ffe7070000 device
TFTP from server 192.168.8.50; our IP address is 192.168.8.45
Filename 'u-boot-dtb.bin'.
Load address: 0x1c00000
Loading: * #########################
         8 MiB/s
done
Bytes transferred = 376686 (5bf6e hex)
## Starting application at 0x01C00000 ...

U-Boot 2023.07-rc2-00004-g1befbe31c1 (May 23 2023 - 18:40:01 +0800)

CPU:   rv64imafdc
Model: Sipeed Lichee Pi 4A
DRAM:  8 GiB
Core:  13 devices, 6 uclasses, devicetree: separate
Loading Environment from <NULL>... OK
In:    serial@ffe7014000
Out:   serial@ffe7014000
Err:   serial@ffe7014000
Model: Sipeed Lichee Pi 4A
LPI4A=>